Sunscreen, nourishing balm, rich body cream… some textures inevitably leave more residue than others.

That's normal.

Glide is designed to help you apply your cream without ending up with greasy hands, but like any reusable accessory, it needs a little cleaning from time to time. Especially after a very rich, sun, or somewhat thick texture.

Good news: cleaning is still simple. No complicated products needed. A little white vinegar, baking soda, hot water, a few minutes… and your Glide is ready to go again. ✨

Why clean Glide after sunscreen or a rich cream?

Sunscreens and very nourishing textures are often greasier, thicker, or more water-resistant.

Result: they can leave more residue in the applicator, on the foam, or around the rollerball.

Cleaning your Glide allows you to:

• maintain clean and hygienic application;
• prevent cream buildup;
• preserve a clean feel when in use;
• change textures more easily;
• extend the life of your applicator.

The idea is not to add a constraint to your routine. Just to keep your Glide clean, especially after the richest textures. 🧴

What you'll need

To clean Glide after sunscreen or a very rich cream, prepare:

• your Glide;
• its base;
• a bowl;
• white vinegar;
• baking soda;
• boiling water;
• a clean toothbrush, if residues remain visible;
• clear water for rinsing.

That's all.

Step 1: Disassemble Glide

Before starting the cleaning, remove the removable parts.

Remove:

• the rollerball;
• the foam.

This step allows you to clean each part correctly, especially if the cream is very rich or has left marks in the contact areas.

Step 2: Clean the body of Glide in its base

Then place the Glide on its base.

Add directly to the base:

• 2 spoons of white vinegar;
• 1 spoon of baking soda;
• then fill with boiling water.

Be careful, it foams! The mixture will help loosen cream residues and clean the inside of the applicator.

Let it act for 10 minutes.

✨

A little tip: do this step calmly after a beach day, a very rich body routine, or use with a sunscreen. Your Glide will be ready for the next application.

Step 3: Clean the foam and rollerball separately

While the body of Glide is soaking in its base, prepare the same mixture in a bowl.

In the bowl, add:

• 2 spoons of white vinegar;
• 1 spoon of baking soda;
• boiling water.

Then place the foam and the rollerball in the bowl. Press the foam slightly so that the mixture soaks in well.

Let it act for 10 minutes as well.

This allows cleaning the elements that are directly in contact with the cream and the skin.

Step 4: Remove residues if necessary

After the 10 minutes of soaking, wring out the products, empty the glide. If you still see residues, use a clean toothbrush to clean the affected areas.

You can brush:

• around the rollerball;
• on small areas where cream can accumulate;
• on accessible internal parts;
  

No need to scrub hard. The goal is simply to help the residues detach.

Step 5: Rinse thoroughly with clear water

Once cleaning is complete, carefully rinse each element with clear water.

Rinse:

• the body of Glide;
• the rollerball;
• the foam;
• the base.

This step is important to remove any remaining vinegar, baking soda, and cream.

Your Glide should be clean, clear, and without visible deposits.

Step 6: Let Glide dry upside down

Finally, place Glide upside down on its base.

This position allows water to drain naturally.

Let it dry before closing it or refilling it.

And there you have it: your Glide is ready. Clean, rinsed, ready to keep up with your pace. 👜

How often should you clean Glide?

It all depends on your use.

You can deep clean Glide:

• before changing creams;
• ideally every week;
  
• if the application feels less smooth.

For daily use with a lighter texture, a regular rinse of the rollerball and foam may suffice between two more complete cleanings.

Can Glide be cleaned with soap?

Yes, you can rinse certain parts with a mild soap if you prefer.

But for very rich or sun textures, the white vinegar + baking soda + hot water mixture is more effective in helping to loosen stubborn residues.

The important thing: always rinse thoroughly with clear water afterwards.

Can cream be put back in immediately after cleaning?

Yes, but only once Glide is thoroughly rinsed and completely dry.

If water remains inside, it can mix with your cream and alter its texture.

The right reflex: let Glide dry upside down on its base, then fill it when it is clean and dry.

How long does it take to clean Glide?

The recommended soaking time is 10 minutes.

With disassembly, rinsing, and drying, active cleaning remains very quick. You prepare the mixture, let it act, rinse, and place it upside down.

Simple. Clean. Hassle-free.

In summary: cleaning Glide after sunscreen or a very rich cream

To clean your Glide after sunscreen or a very rich texture:

1. Remove the rollerball and foam.
2. Place the body of Glide on its base.
3. Add 2 spoons of white vinegar, 1 spoon of baking soda, and boiling water.
4. Make the same mixture in a bowl for the foam and the rollerball.
5. Let it act for 10 minutes.
6. Clean with a clean toothbrush if there are still residues.
7. Rinse thoroughly with clear water.
8. Place Glide upside down on its base to allow the water to drain.

It's ready.

Your Glide is clean, clear, and ready for your next favorite cream. ☀️